DC8-80V 1 Channel WiFi Smart Relay Module Without 433M Remot

Date:2023-09-11 Views:

SKU: LC-EWL-1R-D80

Tech info: http://www.mediafire.com/file/cptpsg5x697x90e/DC8-80V_1CH_WiFi_remote_relay_EN.zip/file

Overview
LCTECH single-channel DC 8-80V remote intelligent WIFI switch is equipped with the original WIFI module of well-known manufacturers, embedded in the IoT intelligent control program, only need one router with Internet access and an Android/IOS mobile phone can realize remote control of the relay anytime and anywhere, also support local buttons, 433M wireless remote control, can be used to upgrade and refit existing home appliances. Make everything smart!

Function features
1.On-board intelligent IoT WIFI module, simple configuration and powerful function
2.Support "eWeLink" mobile APP to remotely control via WIFI and 4G/3G/2G network
3.Supports timing, delay, device sharing, intelligent scene and other control methods
4.Support switch status real-time feedback when both device and APP are online
5.Supports two modes: self-locking and inching. The default opening time of inching is 1S
6.Support local button or 433MHz remote control, independent of WIFI/4G/3G/2G function, can control normally even when the device is offline
7.On-board 1 channel 5V, 10A/250V AC 10A/30V DC relay, can be continuously sucked 100,000 times, with diode effluent protection, short response time
8.Wide voltage supply: DC 8-80V, and the input does not distinguish between positive and negative
9.Output signal: relay switch signal
10.On-board mode selection key,WIFI status indicator, relay switch indicator
11.The PCB board and materials used are lead-free, environmentally safe.

Hardware introduction and description
1.Board size: 78*47 mm
2.Interface description

3.Mode description

(1)Mode types

Self-locking: Press the button to open the relay and it will close when button be pressed again.

Inching: Press the button to open the relay and it will close automatically after 1S delay.

(2)Mode selection

Press the mode key to switch the working mode, default is Self-locking.

The mode indicator on means Self-locking mode, indicator off means Inching mode.

4.Instructions for use

(1)Control with APP

①Scan the following QR code or search the “eWeLink” on the market to install the mobile APP

②Register an eWeLink account first if needed
③Connect to the DC 8-80V power adaptor for the device, press the WIFI config key for more than 7S until the the WIFI indicator blink fast
④Click the “+” button to add device. In this procedure, the APP will let the device connect to your router and register on the eWeLink’s remote server
⑤Wait for the status of the device become online, then you can control the device with APP.
Remark:
1.The device supported 2.4G WIFI signal only, please do not use 5G router for it.

2.If the device can’t be online on the APP, please delete the device and try to add it again

(2)Control with local key

Press the WIFI config key for a short time can also control the relay.

(3)Control with 433M remote control

Press the key A on remote control can control the relay.

The 433M module in the device has been matched with the remote-controller, If you want use new 433M module, please see following instructions:

Matching method: Press the key on 433M module for about 2S, and release the key when the 433M indicator off, then press any key on the remote-controller, it means matching success when the indicator blink 4 times;

Clear method: Press the key on 433M module for about 8S, it means all of the matching has been cleared when the indicator off.

Remark:Under online circumstances,the status of the device will feedback to the APP when control with local key or 433M remote control.

Previous：12V Lead-acid Battery Protector Against Over discharge Modul

Next：DC8-80V 1 Channel WiFi Smart Relay Module With 433M RF

Contact us

Relay Module

DC8-80V 1 Channel WiFi Smart Relay Module Without 433M Remot